Katy, TX

Arrived to a blown 5amp fuse on the furnace control board. Removed burnt fuse and installed my fuse popper to identify any low voltage shortages. Was unable to locate any short at this time. Installed a new 5amp fuse and began testing system heating and cooling. System is heating properly at this time.

Installed new DATs Sensor, zone board in normal operation once installed. Began testing system and discovered E113 error code which indicates high voltage. Tested power coming into the furnace and recieved 124.7v. This is proper power and we should not be having this error code. This indicates the board is bad. Will check warranty and part availability.

Found nothing wrong unit is operating properly at this time no mechanical issue located

Heat Pump Diagnostics and Repair: A heat pump experiencing irregular operation was inspected, revealing a faulty reversing valve. After replacing the component, we restored smooth transitions between heating and cooling, ensuring year-round comfort.

Furnace Repair: A peculiar odor emanating from a client’s furnace prompted our inspection, revealing a clogged burner assembly. We conducted a meticulous cleaning and alignment, eliminating the issue and restoring the furnace to peak performance. The homeowner was educated on routine maintenance to prevent future problems.

Ductless Mini-Split System Installation: A client sought an efficient heating and cooling solution for specific areas in their home. We installed a modern ductless mini-split HVAC system, ensuring optimal placement for the indoor and outdoor units. This personalized system now provides energy-efficient climate control in targeted zones, offering unparalleled comfort.

Replacement both supply and return plenum chalking all supply registers to the ceiling.

Chemically clean the indoor evaporator coil Blower wheel removal and cleaning Clean main duct trunk, Brush all supply and individual Return runs Fog with deodorizer. We use THE Roto Brush Beast DR The best duct cleaning machine in the industry. We will also. Clean the register grills and reinstall them or recommend replacing if they cannot be cleaned. Fog system with deodorizer Up to 20 runs $50 each additional

Replaced suction line temperature sensor. Tested system once installed. System is functioning properly.

Found insulation blocking the fan motor- blower was going off due to being too hot. Ran system and heater Is now working properly at this time.

Found system covered in growth gave estimate for duct cleaning customer excepted the silver option.

Upon arrival I discovered error code 33 on the furnace and error code 196 on the thermostat. Error code 33 indicates a high limit switch trip to which i identified to be the top flame rollout. Was able to reset switch and have the furnace come back on. After about 2 minutes it hit the same switch. Was able to watch the flame at the top of the burners rollout and intermittently hit the flamerollout switch. System will run for 2-5 mins and hit the flame rollout. Verified that it wasn't a bad flamerollout.

Upon arrival customer made me aware that she had some light electrical work done around the house. I immediately checked the main breaker box to ensure all breakers were on which they were. Went in the attic and discovered no power to the unit. Noticed the light switch that controls the power to the system to be off. Restored power and system is now running. Inspected system to ensure operation. System is now heating. Did make customer aware that she has a R22 Evaporator Coil and Condender, as well as a 1996 Ducane Furnace.

Performed fall maintenence for homeowners system. Upon arrival customer stated unit had stopped heating over night and seemed to be heating intermittently. Upon inspection I discovered the dats sensor to be half way out of the supply plenum which is normal for the summer. Adjusted dats sensor for the winter and reset system. System is now heating at this time and all Furnace safties are functioning as intended. Customer asked to have a customer supplied capacitor installed. I checked out the existing capacitor and determined to be functioning properly. Also customer supplied capacitor was the incorrect size.

Performed fall maintance on 2 systems, everthing is operating properly..vhecked all safteis and all safteies are operating properly.

No mechanical issues located system is heating filters have been replaced

Unit came right on when called from the stat

Customer called to have the downstairs system inspected as it was not heating. Identified the flame sensor to be built up with carbon, removed all carbon and debris from flame sensor and system now operates. Inspected the upstairs system as well. Both furnaces are operating as intended at this time and all safties are functioning properly.

Performed fall maintenence for all 4 units. 3 units are operating as intended. However unit 3 heat kit is faulty and recommend replacing at this time. Sent invoice and recommend estimates.

Arrived at customers home to the Control Board displaying a error code for flamerollout. Identified the heat exchanger to be cracked. Diasabled gas to furnace at this time and advised the customer. Put together two estimates for the customers and sent financing paperwork as well. Will follow up next week as customers would like time to make their decision.

Discovered the high limit switch on the blower motor to be disconnected. Likely disconnected when we did the duct cleaning service. Reconnected together and system is operational.

Performed Fall Maintenence for BOTH of the homeowners systems. Both systems are heating as intended at this time. Verified safties for both units to be operating properly as well. Did discover the upstairs furnace to have a chattering transformer. Recommened replacing at this time however homeowner would like to wait till the next visit.

Clean main return duct trunk, Brush all supply and individual Return runs on a system. Clean all registers and return grills. Test all operations. Fog with deodorizer. We use THE Roto Brush Beast DR The best duct cleaning machine in the industry. We will also. Clean the register grills and reinstall them or recommend replacing if they cannot be cleaned. Fog system with deodorizer Up to 20 runs $50 each additional

Duct cleaning option #1 Removed all supply and return grills Cleaned grills and boxes with moldicide Brush all duct runs Cleans mixer boxes Clean supply plenum Cleaned return air can Cleans evaporator coil Clean blower assembly Fog complete duct system Caulk all supply boxes to the drywall System is now clean and running properly

Discovered the thermostat to have come loose from it's base. Adjusted thermostat and reset the system. Inspected package unit on the roof to identify any causes for the problem. Unable to discover any issues at this time. Recommened replacing the thermostat. Customer has declined at this time.